Dwt In Vertue Lv Plans

1ZLV

Copyright 1996 - 2003 Creative Science & Research

48 vdc

OUTPUT

Charged to 24 vdc

25000 uf 50v

Electrolytic Capacitor

Charged to 24 vdc

25000 uf 50v

Electrolytic Capacitor

Please read this it is very important! YOU CAN NOT CHARGE EACH CAPACITOR WITH 24 VDC AND ALSO HAVE THEM CONNECTED IN SERIES ! You must do one or the other never at the same time! 1st you charge each capacitor, then 2nd you disconnect that charge, 3rd you then connect each capacitor ( that now has that powerful 24 volt charge ) and connect them in series. now it would be stupid to connect and disconnect all of this by hand. So what you must do is use switches! You can use all relay switches 1- 4 pole double throw and 5 - 30 amp auto relay switches, or you can use 1- 4 pole double throw relay and 5 - SCR's (Silicon-Controlled Rectifiers.) as switches. ( It is very easy to do!) Using SCR's is much quieter than using loud relays. you can buy low power SCR's at Radio Shack or you can buy High amperage SCR's by catalog. use 70 amp x 200v SCR's for a 1,000 watt unit, or 275 amp x 600 volt SCR's for a 5,000 watt unit. FIGURE #1 is the Charging diagram, this is where you will need to use the 4 pole double throw relay w/1-70 amp SCR on the positive lead, ( Radio Shack type cat. no. 275-214 12 vdc plug in relay. ) This relay is always in the up position, so the capacitors will be charging as soon as you connect the battery to the relay, then when you apply 12 vdc to the coil of the 4 PDT relay it will move the contacts down and this will turn off the charge. All of this will happen very quickly! Because instead of connecting the relay coil to the 12 vdc battery by hand you will be using our MOTOR MICRO SCR SWITCH METHOD The switching must be fast in order to charge the main capacitor bank, which you can apply your load to this, such as a 100 watt light bulb etc... DC only at this point. So you see what we are doing here is eliminating the need to place 10 - 12 vdc deep cycle batteries in series to get 120 vdc. we are simply using capacitors instead. But remember no matter what you do you will always need 10 deep cycle batteries for any average size home. NOTE: You could also build your own relay and use large bolt heads for contacts, and make your own 60 amp 4 PDT contact relay. But its not advisable, Using SCR's as switches work much better!

We Strongly Recommend that you Build a 100 watt inverter first using relays. Use 120 VDC to light a bulb!

THIS IS WHAT A RELAY LOOKS LIKE

CONTACTS

FRONT VIEW OF RELAY

SPRING

How Make Inverter Use Relay

SPRING

12 VDC coil 75 ma electromagnet

FRONT VIEW OF RELAY

1

2

3

4

5

6

7

8

9

10

11

12

13

c

J

14

COIL 12 v INPUT + SIDE VIEW OF 4 PDT RELAY Page 19

TOP VIEW Aluminum Heat Sink w/ SCR 200 amp fig #1

CHARGING CIRCUIT DIAGRAM

TOP VIEW Aluminum Heat Sink w/ SCR 200 amp

200 Amp Solar Panels Charger Circuit

25000 UF 50V

Electrolytic Capacitor

Radio Shack part# 275-214 12 VDC plug- in relay, contacts rated at: 5 A at 125 v

#2 CHARGING CAP BANK

Use 100 amp diodes x 150 to 200 volts

25000 UF 50V

Electrolytic Capacitor

Radio Shack part# 275-214 12 VDC plug- in relay, contacts rated at: 5 A at 125 v

Use 100 amp diodes x 150 to 200 volts

25000 uF 50V

25000 uF 50V

25000 uF 50V

25000 uF 50V

25000 uF 50V

25000 uF 50V

25000 uF 50V

-> -

I==i

25000 uF 50V

#3 THE MAIN CAPACITOR BANK

100 AMP 150V- 200 V DIODE

Please note that SMALLER Diodes can bo connected and stacked in parallel to Increase Input amps.

100 AMP 150V- 200 V DIODE

Please note that SMALLER Diodes can bo connected and stacked in parallel to Increase Input amps.

25000 uF 50V

50 v Electrolytic cap

50 v Electrolytic cap

12 VDC DEEP CYCLE BATTERY

12 VDC DEEP CYCLE BATTERY

30 to 60 amp circuit breaker house type.

YOU MUST USE A DIODE FOR LOAD or for next alternating current phase.

100 watt light bulb

120 VDC OUTPUT at this point.

This is the charging circuit, relay is in the up position and charging each capacitor. Be sure to use 115 vac extension cord wire, 8 amp or more. The more you stack these in parallel the more wattage you will get, and you will also need to use the proper wire size to handle the amperage coming through, If wire is getting almost hot or even warm replace

Do not apply load to #2 charge bank. Only To #3 bank!

TROUBLE SHOOTING: If you have a problem with the #2 capacitor bank shutting down . Then a back calapse has happened and you will need to recharge each capacitor again and then go to each one and discharge It with a discharging wire. ( SHORT THEM OUT ) If this does not help try it again, if that still does not help you will have to take apart each capacitor from one another and charge and discharge again. The capacitors are still good. This should never happen once you have everything In place and fig #2

DIY Battery Repair

DIY Battery Repair

You can now recondition your old batteries at home and bring them back to 100 percent of their working condition. This guide will enable you to revive All NiCd batteries regardless of brand and battery volt. It will give you the required information on how to re-energize and revive your NiCd batteries through the RVD process, charging method and charging guidelines.

Get My Free Ebook


Responses

Post a comment