Capacitor Sheet Method

Again, the more plate sheets of metal you add (or cells ) the more power you will get! Remember it's all about capacitance. You are collecting more than just simple battery type power. The copper plate sheet is the Positive + and the Aluminum sheet is the negative. There are many ways in which one can build this type of earth energy collector, below is simply an example of another shape and form. In this type we use water holes. water holes must all be in exact spots.

Free Energy From Earth
Figure #1 Side View

Copper Sphere

12" Diamter, hollow body

10 to 22 feet high

Negative

1/4" dirt

3 Aluminum sheeting | X 100% Cotton

Aluminum sheeting

Aluminum sheeting

Aluminum sheeting

HV Diode

Copper

Copper

Free Energy From The Earth

Copyright 2002 - 2004 Creative Science & Research

OUR MORE ADVANCED EARTH CAPACITOR!

Copper Wire Layers

Copyright 2002 - 2004 Creative Science & Research

Copper Wire Layers

Free Energy With Wires

pipe

( EECC) Earth Energy Coil Capacitor!

To collect more ether earth energy atoms, build the following Earth Energy Coil Capacitor, Designed & Created by Creative Science & Research. This is far better than anything we have found yet! Much more power and is easier to build.

Start with our EECC Model #1, Take a 5/16" zinc rod or aluminum rod, cut to 7.5" long. Now use #27 bare copper wire, secure it in a drill press ( which you will then turn by hand). Cover zinc rod with paper one layer, use very tiny bits of tape to secure. Now apply the copper wire over the paper, remember to use copper that is not coated! Tape one end of the copper wire to the end of the zinc or aluminum rod and begin to slowly wind. Each wind must be perfectly fitted side by side, paper should be 5.5" long, total length of winds should be 4" long centered on paper. Once you are done with the first layer, apply another piece of paper to the top layer of the first copper layer, do not use to much tape to secure paper in place! Now begin your 2nd layer, repeat this same process until you have about 10 layers, ( the more layers the better!) Copper must not touch the zinc or aluminum. When done hot glue or epoxy a small end piece of the copper wire so it will not come unwound. This is one complete cell, keep in mind this is a small test version, to get more power you have to THINK BIG! Build larger cells, using larger size copper. Then place them in salt water to test, 2 cells can be connected in series, after that you must connect them by use of capacitors, diodes and electronic or hand wound spring switches. If you build 20 of these and try to connect them all in series without a cap/ diode switching method, the cells will cancel each other out. Keep in mind you want water to get to each layer as well as the zinc or aluminum. You can also use Aluminum or zinc pipe.

pipe

Now concerning the paper Die Electric, Paper will not last very long, test and find a water absorbing plastic die electric,( mesh type). We suggest that you use Plastic screen mesh that you can buy at any hardware store, if all you are interested in is collecting small voltages then use one layer in between each layer of copper, if you are interested in collecting higher voltages such as lightning charges then you must use more layers of plastic screen mesh to thicken the die electric so the higher voltages will not short out your system. Paper may not last longer than 1 year, Plastic screen mesh or polyester screen printing mesh will last for many years.

EECC Model #2 Same as #1, but different. In this design we use #27 copper COATED wire, instead of bare wire. since the copper wire is coated and not bare, each layer must be sanded, that is, the top portion of the copper coated layer must be sanded off so it will be exposed to the water and acid, a die electric should still be used in this case. This type makes for a very high efficient earth cap!

EECC Model #3 Same as #1 but reversed! You will use aluminum wire and a copper rod or pipe. Use a 3/4" copper pipe and wind the die electric paper or plastic mesh and Aluminum bare wire around the copper pipe as explained in Model #1

Copyright 2002 - 2004 Creative Science & Research

Copyright 2002 - 2004 Creative Science & Research

Was this article helpful?

0 0
Saving Power, Saving The World

Saving Power, Saving The World

Get All The Support And Guidance You Need To Be A Success At Helping Save Power. This Book Is One Of The Most Valuable Resources In The World When It Comes To How To Use Renewable Energy As Your Alternative Power Suppliers.

Get My Free Ebook


Responses

  • Charity
    Are we use wire mesh of zinc and aluminum for solar air heater?
    8 years ago

Post a comment