Timing the Fuel less Engine

#362

To get an idea of how a DC brush motor works, take apart any size DC motor and check it out. Study it carefully. Timing the Fuel less Engine: 1,000 vdc is applied to the brush assembly, the brush assembly acts as an on and off switch for each set of magnets. The brush assembly can be made in many ways. The timing takes place in two places, the spark plug caps or the commutator brush collar assembly. You will only need one 1,000 vdc charging and firing system that is rated at 1 to 3 amps, the more amps the better, but the more danger to you during assembly. You can experiment around with a low milliamp cap bank and power supply, 10 ma is safe to use. You will need two spark plugs, two sets of capacitor banks or capacitors and one or two diode banks. One diode bank is for the Positive side and optional a 2nd is for the negative side. When the rotor arm magnets #5 & 6 are in the 12:00 position contact should be made to fire #1, #5, #6 & #3 magnets all at the same time. Wire these magnets so they are north pole to north pole, or north to south which will cause motor to then be an attraction motor. Many think that an attraction motor is better? But if you are using this as a repelling motor then time the firing when the arm #5 is just 1/16" past the center of #1 stator magnet. This will insure that the rotor arm will be pushed and rotated to the left and rotate counter clock wise. If timing as an attraction motor, you will want #5 to fire at about 3 to 4 inches before it gets to #1 magnet. This motor can be times to run clock wise as well. Collect all back emf per coil using a diode and capacitor per magnet, on the negative side outputs. It is strongly recommened that you build our 1 hp motor to get more understanding of how to build this motor.

If you choose to use a spark plug, you can gap the spark plug to fire a little early which will cause your power up time tobe less, But you will have less shaft torque (HP). In other words you will have more RPMs but with some what less Horse Power, Now this is not real bad because it depends on what kind of generator you're going to use.

Please NOTE: the engine must be timed just right so the rotor magnets do not repulse each other too soon. Repulsion must take place at center or 1/16" past left or right. ( This prototype uses a 115 volt AC generator, Please note: This engine design rotates to the left only, ( counter clock wise.) You can design it to rotate both ways. Also Note: A & B Magnets connect to the same + & - Brush Rotor Assembly.

Update: See our new and easy way to make a homemade commutator which should be included with these plans.

Brush Assembly Side View see page 7.

SPRING BRUSH CONTACTS

Brush Assembly Side View see page 7.

SPRING BRUSH CONTACTS

Capacitor Banks For Fuelless Engine

WIRE, TO HOOK UP BOTH CONTACTS TOGETHER. SEE PAGE 7.

SHAFT HOLE FOR SHAFT TO GO THRU

BOLTS TO ATTACH ADJUSTMENT ASSEMBLY TO COLLAR.

PLASTIC SPACER / WASHER

NEGITIVE WIRE HOLE TO ROTOR MAGNETS

WIRE, TO HOOK UP BOTH CONTACTS TOGETHER. SEE PAGE 7.

cap bank #2

PLASTIC SPACER / WASHER

SHAFT HOLE FOR SHAFT TO GO THRU

BOLTS TO ATTACH ADJUSTMENT ASSEMBLY TO COLLAR.

=Firing

NOTICE: If you are having trouble understanding all of this, please keep studying it and do some small scale experiments to help you.

PLEASE NOTE: WE DO NOT HAVE TIME TO GIVE YOU ANY TECHNICAL SUPPORT, THIS ENGINE DOES WORK, MANY ALREADY HAVE WORKING MODELS. The Library is loaded with books on electronics, electrical engineering, electric motors etc... children's books have the most for learning the 1st basics. Please do not attempt this engine unless you have some head knowledge in High Voltage and electricity. PLEASE BE CAREFUL ALWAYS WEAR RUBBER GLOVES AND SHOES WHEN WORKING AROUND HIGH VOLTAGE.

cap bank #2

Capacitor Bank For Fuelless Engine

=Firing

Fulless Engine

Creative Science & Research Copyright 2002

Solar Panel Basics

Solar Panel Basics

Global warming is a huge problem which will significantly affect every country in the world. Many people all over the world are trying to do whatever they can to help combat the effects of global warming. One of the ways that people can fight global warming is to reduce their dependence on non-renewable energy sources like oil and petroleum based products.

Get My Free Ebook


Post a comment